联系我们
名称：燃气燃烧机良心厂
电话：xxx
手机：xxx
邮箱：xxx
地址：xxx
新闻动态
燃气燃烧器操作
燃气燃烧器操作
Gas burner operation
因为燃气燃烧器主要燃料分天然气、液化石油气、城市煤气及其他可燃气体，这几种燃料属易燃、易爆的危险气体，在使用和储藏过程中都应对安全引起高度重视，否则将发生重大安全方面的事故。
Because the main fuels of gas burner are natural gas, liquefied petroleum gas, city gas and other combustible gases, these fuels are flammable and explosive dangerous gases. Safety should be paid great attention in the use and storage process, otherwise major safety accidents will occur.
(一)、开机操作:
(1) Boot-up operation:
1.对新安装炉体，调试前应认真检测燃气是否符合燃烧器的要求;检查供气管路上的检测仪器是否正常及管道阀门开、关是否正常，是否便于以后使用及检修。
1. Before debugging the newly installed furnace body, it is necessary to carefully check whether the gas meets the requirements of the burner; check whether the testing instruments on the gas supply pipeline are normal, whether the pipeline valves are open and closed properly, and whether it is convenient for later use and maintenance.
2.对新安装的管道，应认真检查所有管路的安装可靠性和管路的密封性。
2. For newly installed pipelines, the installation reliability and sealing of all pipelines should be carefully checked.
3.使用单独气化站的用户，要保证供气量、供气参数符合安全燃烧要求。
3. Users using separate gasification stations should ensure that the gas supply capacity and parameters meet the requirements of safe combustion.
4.操作人员认真阅读设备使用说明书，熟练掌握安全操作知识及方法。
4. Operators should read the instructions carefully and master the knowledge and methods of safe operation.
5.每次开机前要检查燃气阀门是否打开，否则燃烧器不工作。
5. Check whether the gas valve is opened before each start-up, otherwise the burner will not work.
6.启动控制柜上的电源控制按扭，此时数显表就显示当前炉内温度，新安的装炉体此温度为环境温度。
6. Start the power control on the control cabinet and press the torsion. At this time, the digital display shows the current furnace temperature, which is the ambient temperature of Xin'an furnace body.
7.启动风机控制按扭，安装在炉体上的风机就工作，此时若风机损坏控制柜就自动保护不进入下一步操作。
7. Start the fan to control the torsion, and the fan installed on the furnace body will work. At this time, if the fan damages the control cabinet, the automatic protection will not enter the next operation.
8.助燃风机工作无异常现象时，再启动燃烧控制按扭，此时燃烧程序控制器就开始工作，它通过一定的程序进行点火、送气、检测火焰、等程序最终实现安全燃烧。
8. When there is no abnormal phenomenon in the operation of the combustion-supporting fan, the combustion control press is restarted, and then the combustion program controller starts to work. It finally realizes the safe combustion through certain procedures such as ignition, air supply, flame detection and so on.
Gas burner operation
因为燃气燃烧器主要燃料分天然气、液化石油气、城市煤气及其他可燃气体，这几种燃料属易燃、易爆的危险气体，在使用和储藏过程中都应对安全引起高度重视，否则将发生重大安全方面的事故。
Because the main fuels of gas burner are natural gas, liquefied petroleum gas, city gas and other combustible gases, these fuels are flammable and explosive dangerous gases. Safety should be paid great attention in the use and storage process, otherwise major safety accidents will occur.
(一)、开机操作:
(1) Boot-up operation:
1.对新安装炉体，调试前应认真检测燃气是否符合燃烧器的要求;检查供气管路上的检测仪器是否正常及管道阀门开、关是否正常，是否便于以后使用及检修。
1. Before debugging the newly installed furnace body, it is necessary to carefully check whether the gas meets the requirements of the burner; check whether the testing instruments on the gas supply pipeline are normal, whether the pipeline valves are open and closed properly, and whether it is convenient for later use and maintenance.
2.对新安装的管道，应认真检查所有管路的安装可靠性和管路的密封性。
2. For newly installed pipelines, the installation reliability and sealing of all pipelines should be carefully checked.
3.使用单独气化站的用户，要保证供气量、供气参数符合安全燃烧要求。
3. Users using separate gasification stations should ensure that the gas supply capacity and parameters meet the requirements of safe combustion.
4.操作人员认真阅读设备使用说明书，熟练掌握安全操作知识及方法。
4. Operators should read the instructions carefully and master the knowledge and methods of safe operation.
5.每次开机前要检查燃气阀门是否打开，否则燃烧器不工作。
5. Check whether the gas valve is opened before each start-up, otherwise the burner will not work.
6.启动控制柜上的电源控制按扭，此时数显表就显示当前炉内温度，新安的装炉体此温度为环境温度。
6. Start the power control on the control cabinet and press the torsion. At this time, the digital display shows the current furnace temperature, which is the ambient temperature of Xin'an furnace body.
7.启动风机控制按扭，安装在炉体上的风机就工作，此时若风机损坏控制柜就自动保护不进入下一步操作。
7. Start the fan to control the torsion, and the fan installed on the furnace body will work. At this time, if the fan damages the control cabinet, the automatic protection will not enter the next operation.
8.助燃风机工作无异常现象时，再启动燃烧控制按扭，此时燃烧程序控制器就开始工作，它通过一定的程序进行点火、送气、检测火焰、等程序最终实现安全燃烧。
8. When there is no abnormal phenomenon in the operation of the combustion-supporting fan, the combustion control press is restarted, and then the combustion program controller starts to work. It finally realizes the safe combustion through certain procedures such as ignition, air supply, flame detection and so on.
